Posts

Chosen Solution If i call someone the screen goes black and does not turn on again Sounds like a problem with the proximity sensor. I have seen this happen when we worked on a device and had the proximity sensor seated incorrectly. Probably not what happened here unless you have repaired the phone or it has been dropped possibly. Restarting the phone should fix the problem temporarily until you make a call again....

Chosen Solution I turned on my Panasonic Plasma TV model TC-P55VT30 television today with the remote (I don’t think this model has a physical power button on the TV). After a few seconds, I heard a click from the TV and the screen was off. My PlayStation and other devices are getting power from the same outlet so it’s not power. I’ve heard about red light codes etc for these TVs and though I’d never noticed one before, there is definitely no light blinking now....

Chosen Solution I have a Kenmore elite top load maybe 8 yr old. My drum does not spin and makes a clicking sound after the rinse cycle and then I move the button and then it engages and starts working? Help Cause 1 Lid Switch Assembly The lid switch assembly prevents the washer from spinning when the lid is open. If the lid switch assembly fails, the washer may stop mid-cycle....

Chosen Solution replaced broken digitizer, then the LCD started to show lines. Replaced screen, all looks great except the digitizer does not work properly and the screen jerks but doesn’t swipe (to open or shutdown) Any ideas whats wrong or what needs to be replaced? Thanks NK The iPad mini is pretty temperamental and fixing it requires good quality parts and attention to detail. You need to go back and double check all your steps....

Chosen Solution My camera taking dull images even i set maximum resolution. How can i solve this problem? and how to clean my camera lence? the resolution have no impact on the sharpness of the picture. could you upload a sample image? are all images “dull”? cleaning the lens inside or outside?? a dlsr works different than a compact camera - one of the main differences of the picture is the blur - or better - the bokeh (click)....

Chosen Solution Has any one got a wire-ing schematic for this model Camry? Has the 5S-FE Engine. Not sure if this has been resolved yet, but check your relay and see if it is the culprit. Try this link see if it works for you.

Chosen Solution Will not power on .. took it to Apple they checked battery and did reset and worked for a week .. and stop turning on again .. they checked battery and said it’s fine .. and want 600 to fix .. more then it’s worth . Any ideas You may try popping off the bottom cover, unplug battery and then plug in MagSafe adapter, if system starts up on its own and works flawlessly it might be a battery issue you can try to resolve by replacing battery....

Chosen Solution Hi, I got a water damaged iphone 5s. I removed the shields on the logic board and cleaned it with 90% isopropyl alcohol. I tried to power it on with a working LCD and battery but still no power. I am trying to learn micro soldering. So my question is which chip should be replaced? And how do I test which chip(s) are bad before replacing any. I have a multimeter....

Chosen Solution Post Answer MacBook Pro 15" Core 2 Duo Models A1260 Hi, after lending my macpro to a friend for usage for projection in a large auditorium. It came back with no sound coming out from onboard speakers, system preference also indicated that “headphone” is the only output. If external speakers are attached, the sound is ok. I suspect the left i/o card is damaged. Pls advise on which part/s to buy so that i can start the repair....

Chosen Solution My Macbook Pro late 2010 suddenly stopped working Num keys 1~9, however num key 0 works. I already tried setting RAM but doesn’t work. Please help Here’s the IFIXIT guide for the MacBook Pro 13" Mid ‘11 model Upper case replacement. Sorry to say the keyboard is part of this assembly. While some people have managed to get from China directly just the keyboard sub-assembly it is a bear to replace as you’ll need to remove about 50 screws or snap rivets....

Chosen Solution I’ve recently bought a 3DS. It can only work when the charger is plugged in. The charger can charge the battery (I’ve checked with a multimeter and a spare battery). When I unplug the charger the device shuts off. 3DS also automatically powers on when I plug the charger cable. I checked the power button but when the device is open it functions properly. I haven’t found any postings with similar issue....

Chosen Solution everything is super muffled, in-call and on recordings such as base camera app and snapchat. however, speakerphone works just fine. Hi @pls_help , Use a bright light and a magnifying glass to check that the voice inlet hole at the bottom of the phone is not blocked with lint or dust. If it appears to be blocked DO NOT use a pin or probe to try and clear it as you might damage the microphone which is directly behind the hole....

Chosen Solution MacBook Core 2 Duo 2.2 GHz 1GB RAM (2- 512K) 120 GB Hard drive This one has me baffled. It came in able to boot up to the desktop and the mouse was frozen. The mouse ran fine when booted from 10.5 full retail installation disk. Ran disk utilities - no problems. Repaired permissions till clear. Still mouse is frozen on reboot. Attempted system re-install. Tells me 10.5 cannot be installed and to look at the system requirements....

Chosen Solution My 55k 8000 picture slowly wavers then the entire screen shows vertical lines. Takes about 15 minutes. If I turn it off, then on, picture starts well then this scenario repeats. Update (09/05/2019) @djm1803 could be a bad t-con board or main board. Post some pictures of what your screen shows and of all the boards so we can try and help you further. Adding images to an existing question

Chosen Solution Hello, I just found a iMac G3 logic board in my basement. I want to get it to work, but a lot of the parts from the Mac are missing. The logic board is still in one piece though! Does anyone know the Pinout for the power connector on the mainboard? It’s this one: so far the only thing I have is iMac Power Connector 1 +3.3 VDC 2 +12 VDC 3 Ground 4 +5 VDC 5 Ground 6 +5 VDC 7 8 Ground 9 10 Ground 11 Ground 12 +3....

Chosen Solution The glass that covers the camera on my Pixel 6 is completely shattered, I want to replace it myself. Is it something can replaced by its self or do i need to replace the whole back? I haven’t found anything anywhere about how to replace it. Hi, Here’s a video that shows how to remove/replace the rear camera lens glass. Replacement glass lens parts are available online. Just search for Rear Camera Lens Glass for Google Pixel 6 to get results for suppliers that suit you best....

Chosen Solution The replacement for this phone is currently in the mail but I am really hoping to get this one working for an hour just to get the pictures etc.. off. The power button is stuck down without any event (being dropped) triggering it. I took the thing apart and the actual little white button will not click anymore like the volume ones do. When plugged in, the red LED does not appear and it doesn’t charge....

Chosen Solution Hi, I was asked by a friend to replace the glass on his P9. All went well till the part where I had to reattach the assembly to the metal chassis. Since I couldn’t find pre-cut adhesive, I used the classic double-sided tape for the top and bottom edges (3M). The thing is, the bezels are so narrow that the 1 mm tape would prevent the screen from fitting properly....

Chosen Solution I have a Powermac G5 dual 2.5 GHz (June 2004) with LCS (liquid cooling system) system that I would like to sell, and I noticed that the operating temps of the CPUs are in the range of 73 to 78 degrees C. I got this system with no power supply from craigslist. I was going to sell the CPUs + LCS assembly, but there were no buyers on ebay, not even any lowball offers....

Chosen Solution Sure you can fix it, here’s a video on how to do it: https://www.youtube.com/watch?v=Cee-2The… Yes you can fix it. If the wire was chewed off close to the earbud,that’s good. Length won’t be a huge deal. Just pop the earbud open,and strip the wire. There are 2 tiny wires inside. Those wires are coated with a thin layer of enamel. It looks shiny on the wire,which is why the red wire looks like red copper,but it’s actually red coating....