Posts

Chosen Solution When I press the On button my printer begins to start but then stays in “Startup” mode and won’t continue to boot up. To turn it off I have to unplug the power cord because none of the buttons on the control panel will work. Hi, What is the exact model number of your printer, is it 3, 3.2 or 3.2s? You may be able to fix your problem by reloading the firmware but because the firmware is different for the 3 models you need to install the correct one otherwise it may render your printer inoperable....

Chosen Solution My blu phone keeps rebooting Hi carolineforbes28, Check out this troubleshooting page for potential solutions to your rebooting problem. There could me many reasons why your phone reboots on its own. If you know it’s not the battery, and you’ve already tried a hard reset, the problem may be with the motherboard. I hope the troubleshooting guide helps! worst phone ever… sorry i bought one My BLU phone was rebooting all the time....

Chosen Solution my fridge aint cooling but my freezer is what can i do Cause 1 The Evaporator Coils are Frosted Over The defrost heater assembly turns on a few times throughout the day to melt away any frost that may have accumulated on the evaporator coils. If the defrost heater assembly is defective, frost will continue to accumulate on the evaporator coils, and the coils will become plugged with frost....

Chosen Solution my phone screen remains black after pressing awake power button even. After couple of time press buttons it does awake randomly and I can use it and again it goes black. screen on and off. I also change new screen original and compatible , it still same. How do you think the problem and solution could be ? You’ll need to closely inspect the Power Button flex and connector to see if it isn’t damaged....

Chosen Solution My iPod died and now when I try to charge it nothing happens. If you haven’t dropped it or gotten it wet, it probably needs a new battery. Here’s the instructions on how to replace it: iPod Classic Battery Replacement Here’s where to get a lifetime guaranteed battery for $14.99: http://store.kokopellimusic.us/product_p… I haven’t seen where Ifixit has this battery listed.

Chosen Solution It’s okay when I adjust one video (Motion app). However, after I add another the one, it starts pausing and slowing down. I can’t move my computer mouse. Motion 5, Adobe After Effects and Photoshop are very processor-intensive applications that also use a lot of RAM. Opening one of these apps will likely use up a big portion of your memory, let alone opening two. The lag that you’re experiencing is probably the laptop having to reallocate its memory....

Chosen Solution I can move mouse cursor but clicking by mouse pad is not working. Have you checked your battery? I had the same problem with mouse pad not working and an Apple technician took a look at it and it was the battery had swollen up so it had pressure on the top. Apple gave me a new battery and the mouse pad works like a charm. I had replaced my hard drive using directions from ifixit (thanks!...

Chosen Solution My Pebble Steel watch is not vibrating when I receive a new notification. I can still see when I get a notification because it pops up on the screen but I don’t feel the vibration. I have made sure that the settings on my phone and watch are both set to vibrate for a new notification. What else can I do? Also, try visiting the troubleshooting page for more help....

Chosen Solution My phone does not charge or turn on, I connect the charger but it does not start the charge, I put the battery in another phone and it works fine. help please that can be. Thank you Hi! I think you should replace the charging port. Maybe the IC has gone bad or something. Follow this guide until step16 to see how. Check you power connector maybe its loose or Some dirt inside....

Chosen Solution Hi my projector is heating up and turning off I think that the fans it has are not working wear can I get them or wear can I get it fixed Take them out and check for a reference. If you cant order the exact same ones, order one with the same Voltage / Amps / Airflow

Chosen Solution So I got a cracked phone. It was a moto g from 2013 or15. Awhile ago I dropped it and the screen behind the glass broke. I tried to use it. Before the internal screen broke, I went to a shop and asked the guy how much. He tells me it costs 100$. I’m not sure if the cost has gone up.. Lori Smith , Below are link to enable you to replace the screen yourself and where to purchase....

Chosen Solution My screen suddenly stops touching and it starts flickering grey stuff on the screen, while this happens I cannot use the touchscreen, and stuff just sytarts typing or touching on its own, I have to bend or press the screen and phone before it disappears and it starts touching again, sometimes but rarely does it disappear on its own. I have had the phone for a year, and this started a few weeks ago....

Chosen Solution Hello, i am working on the repair of a Macbook Pro 15" i7 The macbook has very little water damage. and 2 components are damaged. i hope somebody can help me to identify these 2 components. In the picture i placed 2 red circles around them. 1st is a resistor of which i would like to know the value. 2nd is a transistor (i think) which i would like to know the type or the marking that’s written on it....

Chosen Solution I replaced my Macbook’s battery (after following the guide from iFixit) and the computer did not recognise it. The only way for me to turn it on was to plug in the MagSafe connecter (which only showed the green light). I then asumed it was a problem with the replacement battery (from eBay) and put back the original battery. For some strange reason, the original battery wasn’t recognised either!...

Chosen Solution My SNES has stopped working, measuring the output of the power cord, the max I got was 1 volt, does this mean it is the power cables fault? This all started when the console fell, so I have checked the insides of the console and the charger, the console looked completely fine on the inside. I tried to measure from the chargers transformer itself but I don’t know which parts to put my prongs on....

Chosen Solution When I first got this Mac there were no LEDs on when plugged in. I switched out the power supply to get the 1st LED to turn on. However, the Mac still wouldn’t turn on. I could hold the power button and plug in the power cord to get the fans running but that was it. I then switched out the logic board thinking maybe that was the issue....

Chosen Solution Hi; A few months ago I noticed my iMac acting strange, with my screen not refreshing and everything on the screen would have residual images. I did some searching on the apple boards, and others were saying it has to do with the fan not working properly and overheating. They recommended I used smcFanControl, which has done the trick so far. Is there a permanent fix to this? Something I can replace?...

Chosen Solution Everything is working except the sound. Hi, Have you verified that the mute option has not been selected? Since you do not state the model number, have you ensured that the Audio output selection is for the TV’s internal speakers and not for an external speaker option. Check in the Audio settings area of the TV’s Menu. If your TV has a headphones socket, check to see if there is audio there....

Chosen Solution We have a Cannon PIXMA MX472 and we are getting an error code “5b02”. We researched how to fix this error and it led us to a “button combination” that did not work. We then tried to remove the ink cartridges to get to the ink absorber pads but with the error, it wont expose the ink cartridges in a position to remove them. 5b02 is the more cryptic waste ink pad error on some Canon printers, while others directly say the ink absorber is full....

Chosen Solution im an aspiring photographer and would love to just use iphone 4s camera to take pictures and make videos. i have an iphone 4, but was wondering if its posible to have the camera replaced with the iphone 4s.. No the 4 and 4S have completely different flex cable and flex cable connector on logic boards. So the cameras are not compatible and not interchangeable. The pin numbers are different....