Posts

Chosen Solution my iphone is dead beacause i conneted to v8 to iphone conneter to charging after some time i cheaked the conneter is very hote and the phone dont on thatb only says charging logo what i do If your screen is showing the charging logo it will not be fried. The first thing you need to do is replace the battery. If it’s still showing the same symptoms it would point to a damaged charging IC “Tristar or Tigris” from the excess voltage....

Chosen Solution My jeans have a hole; how do I patch them? There are a lot of ways to patch jeans. You can use an external patch, either sewn or ironed-on, a reverse appliqué, or a snazzy zig-zagging thread pattern. Whatever you choose, we’ve got guides to help you through.

Chosen Solution I charged my phone it still wont turn on, when i plug it on the computer it pop up but i cant do anything to it. I did the hard reset ,nothing work.screen is black. Can you try using a different charge cord if that doesn’t help the next step is to replace the battery. If there’s still no joy then the charging port is the next step tear down shows how to get to battery and the charging port to replace iPhone 5c Teardown You may also want to try a force restart How to Force Restart an iPhone 5c hope this helps

Chosen Solution My niece gave me the laptop but when I tried to restore it I started seeing the startup repair and it says it can’t fix it. Is there anything I can do Hi, What OS is installed? If it is Win 8.1 or Win 10 you can create a a recovery USB drive from another laptop or PC which has Win 8.1 or Win 10 installed depending on what you need....

Chosen Solution By turning temperature setting knob back/forward from its “OFF” position to different cooling temperature positions a couple of times, the thermostat will trig on compressor working till 4C temperature setting point. After that, this refrig will not trig on by itself when temperature inside raises. When I start over to play same temperature setting knob again, it will work again at same pattern. Does this indicate the thermostat (temperature setting knob) fails and needs a replacement?...

Chosen Solution After disassembly, a white part remains which fell from the case… And I cannot find its location at all… :( And I don’t know what it is for (part of sort of switch?). Could you guide me to replace it? Many thanks! Vio & Antho M&P looks like you may have some connectivity issue. That is your camera’s WiFi antenna Here is how to reinstall it That curved end wire appears to be a microswitch actuating arm....

Chosen Solution Hi, Can anyone tell what’s happening with my MacBook battery? Its just 2 months old battery and was working fine until last week when it had sudden drop in charge from 40 - 0%. Then I did a SMC reset and battery calibration where it appears to be normal now with the run time but still the status info is wrong in both system and coconut battery app. Please check the attached....

Chosen Solution Apple MacBook Pro 15-Inch “Core i7” 2.4 Early 2013 Specs Identifiers: Retina Early 2013 - ME664LL/A - MacBookPro10,1 - A1398 - 2673 https://everymac.com/systems/apple/macbo… The RAM cannot be upgraded. Here are the storage sticks available for your machine: https://eshop.macsales.com/upgrades/macb… Here’s how to install a new one: MacBook Pro 15" Retina Display Early 2013 SSD Replacement

Chosen Solution Hi, My AirPort Extreme started restarting itself repeatedly so I disconnected it from the power supply for A few minutes and then plugged it back again. Since then the unit Ethernet ports are blinking green but the station main front light remain off. What can I do? How do I make it work again? Thanks, Tal You’ll need to open it up to see what it looks like inside you could have a simple problem or it could be complex to the point of not being worth fixing....

Chosen Solution I’ve got a big problem with my airport card. I’ve got a Mac Book Pro 17" 2.5 GHz Intel Core 2 Duo (Model Number: A1261) of 2008. My airport card worked very well till one day that I lost my connection unexpectedly. The only one message is: “Airport: Off” and “Turn Airport On” but although I try to turn it on the airport stays off. I’ve changed the card, thinking that was the problem, but isn’t it....

Chosen Solution Got an iPhone 6 water-damaged & completely dead. After microscope inspection I found a cap (C0612) beside the NAND which was badly blackened so removed it and the phone began to draw normal boot current (970mA). However there is no image, so I tested the LCD connector (J2019) in diode mode. Nearly everything was fine with 1 exception; Pin 3 (PP5V7_LCM_AVDDH_CONN) is reading open but should be .649 according to my (definitely) known-good board....

Chosen Solution I’ve looked through the entire forum, but haven’t found anyone who posted their diagnostic results with any answers. I’m running in circles at this point. I’m trying to determine if it is the logic board, power supply, or DC power cable from PSU to Logic. System does not power on at all. State 1: LED #1 comes on - which means standby power is present. Pin 1 & 4 - has 12v Pin 1 & 11 - has 12v Pin 1 & 12 - has 0v If I hold the power button on for 3 seconds: State 2: LED #2 however, never comes up or blinks during this whole process....

Chosen Solution So I’ve seen this problem on a few forums. The phone works fine unless you make a call. When you do, the mic and the speakers will not work. They function with any other application in the phone. The suggested fixes are firmware update (some claim this has worked) and the other is a reflow of the chip that handles the incoming calls(?). I know by the teardown which chip handles the sound on the board, but if anyone has encountered and fixed this issue before, could you give a brother a hand on where to aim the heat?...

Chosen Solution Hi, this is my first question here. I own a repair shop and do repairs on iPhone’s for at last 3 years. Now i got a iPhone 6s that drives me CRAZY!!! A customer brought it in for a backlight damage, as always i checked the FL4211 for damage, none to bee seen also no burning, after i took of the CPU shield and the D4021 was a bit raised so i replaced it, after that the backlight came on and worked like a charm....

Chosen Solution My 2 year old Maytag dishwasher (MDBH969AWW3) is out of warranty. talked to maytag and they said i would have to call for service. i tried unplugging, let it sit for several hours and then plugged it back in. it still blinks. i can make it go in a drain cycle by pushing the drain button on top as soon as i plug it in, but as soon as the normal light starts blinking, it shuts off....

Chosen Solution Kenmore elite catalyst Makes like a bearing noise .on all cycles and water is not draining Cause 1 Drain Pump Sometimes, small objects or articles of clothing can get caught in the drain pump. To determine if anything is blocking the drain pump, remove the drain pump and check the pump for obstructions. If the drain pump is clear of obstructions, but is still noisy during the drain cycle, replace the drain pump....

Chosen Solution Hey everyone, Another strange thing happend today.. i have an iphone 5 c , the old screen was cracked , and the digitizer was broken, could not open the phone.. so i ordered a new screen ( from ifixit) installed it ( it is not the first time i replace a screen..) but i don’t have picture. no apple logo or whatever… i tried the old screen ( i had picture but i could’t use the digitizer…) but when i installed the old one again , i had no picture as well…....

Chosen Solution Had dropped my blackberry passport in water during a party removed it out and tried to switch it on but it didn’t and is now dead. Yesterday I plugged it into the charger the led blinked the red light but today nothing happened I really don’t have money to buy a new main or the motherboard pls help on how to get it on and back to life pls help me friends pls...

Chosen Solution i broke my phone recently for the second time…..first time screen broke…got the parts fixed it, was all good…….this time it was the touch screen that cracked…and a little while after it went black….didn’t think much of it and ordered the parts…… I’ve replaced the screens over but still no display, i held it up to the window and saw the screen faintly, so i took the screen off the phone (still connected) and i could see my display when it was held up to the light at an angle…....

Chosen Solution So at WWDC this year, they announced 802.11ac wireless for the new 2013 MacBook Airs. Is it possible to replace the 802.11g card in my 2012 Macbook Air? I assume the wireless cards are not off the shelf products so I would have to buy it from a third party manufacturer or parts from a broken 2013 MacBook Air, both of which seem unlikely. Thanks! Until Apple ships a system and iFixIt tears it apart no one knows what Apple did on the inside (needed changes or if the WiFi connector is the same)....