Chosen Solution My tablet keeps flashing on and off whn it’s in its case but OK whn not in case Maybe the case is pressing the on-off button rapidly? What do you mean by “flashing”?
Chosen Solution I charged my tablet but no matter what I try I can not get it to turn on. This may be several issues. The problem may be either a bad motherboard, a faulty display, or a bad battery. Refer to the troubleshooting page for each. Try one, and try to power it on. If that still doesn’t fix the issue, try the other and try to power on again....
Chosen Solution hi. my usb port in Dell D600 is dead. No power come into USB at all. What usb chip that i have to change ? thank I would just recommend getting a PCMCIA USB card. I don’t think you can find the replacement chip. Also, your ports may just be broken, which involves soldering.
Chosen Solution @Jon Ridley I have a late 2009 27" iMac and need to replace the failed Seagate hard drive. I just skimmed through the web page you linked to and, if I understood correctly, the following is the suggested solution for my case: you wrote: “This is what led me to the discovery of an external thermal sensor cable that works with these two generations of iMacs. This cable is used on the LCD panel of the 27” 2009 and 2010 models, but has the same connector as the hard drive sensor cable and operates in the same range as the SMART disk does, so functions as a great alternative in these generations of 21....
Chosen Solution Hi, everyone I need some help with with my Imac. The thing is that a couple of months ago it started to fail and I had to disconnect before power it on at the point that one day stop working. I already check the diagnostics leds and there is no leds on… What you guys think ? Power supply ? Any recommendations where I can buy it, I’m looking for a cheap solution so I don’t mind if is refurbished … Thanks; Elliot...
Chosen Solution I followed the guide for macbook pro mid 2012 13inch on replacing left speaker. After reassembly, no more power. Not charging. Only very dim green color of magsafe charger. What did I damage? Check that your magsafe board wiring to connector have not been pinched when putting back in place the logic board, it may happen if one hasn’t much practice with the job. A faint green light shows something is faulty in the early part of the main power line....
Chosen Solution Third party parts will usually give you third party problems Try this iPhone 5s Lightning Connector and Headphone Jack Use this, just in case iPhone 5s Lightning Connector Replacement I’ve heard of heating the Baseband chip for 4-5min at 400f and it fixing it. but first try backing up and restoring. if it throws error -1 then try reflowing the chip. Im not 100% sure about the battery issue you are having, but check the time on your phone....
Chosen Solution Hey Guys, So I fix computers a lot, but this one has baffled me. My friend gave me her MacBook Pro that she bought second hand, because the power button doesn’t turn the computer on. First I though the battery could be dead, or the board could have died. After further diagnostics, I found that if you unplug the battery, plug it back in, press the power button, and then, once you connect the power adapter, it boots up....
Chosen Solution My Asus x200m can’t recognize it’s SD card reader. It happened after reinstalling of win 8.1. Is it possible to fix this? Thank you very much The problem was solved with this driver, but I have the same problem with the bluetooth card also. Have a nice day, Ivan ok here is the download for your card reader: http://dlcdnet.asus.com/pub/ASUS/nb/Driv… You may need the latest version of the SD card reader driver straight from the components supplier (realtek)....
Chosen Solution My display won’t turn on at all. There is no sign of the display receiving power and there is no blicking light at the power button. I have a working power adapter brick tested by Apple. Is this a power transformer or monitor inverter problem? Before you do anything else hook up an external monitor. If the video there is good your power supply and logic board are ok....
Chosen Solution My iphone 3 is approximately 2 years old and will not take a charge. I purchased new chargers but this did not solve my situation. The battery symbol continues to stay in the red zone rather than switching to green. There is a choice of 2..1st is a new battery, likely yours is 2 years old and ending it’s life. If you have noticed that it was hard to charge/took longer to charge/random crashes, then that may be the culprit....
Chosen Solution My iPhone 4 has a new kind of screw. What type are they and what tools do I need to remove them? I included photos here: http://yfrog.com/0rx9qjx Hey Kashar, I tried looking at your pictures, but it’s still very difficult to see the screws. Could you light up the bottom of the phone with some good lights (bring the bottom of the phone close to a desk lamp, etc....
Chosen Solution The camera on my iPhone 6S+ has recently begun shaking uncontrollably for absolutely no reason whenever the app is open. Video timelapse, everything is affected the same way, no matter what app is used. I’ve scoured the internet looking for others having the same problem, and I have found plenty of 6+ users but no 6S+ phones affected. Does anyone have a quick fix or do I need to send the phone back?...
Chosen Solution When I want to start the machine, I need to push at least 20 times the start button. Each time I click the display turns on, but the start-up process is not ignited. On the contrary when I click to shut down the machine the button reacts immediately. I already changed the start-up button, but that did not work out. It seems to be an electrical problem on the circuit board....
Chosen Solution My mobile is taking up 8 hrs to get charged, sometimes charge percentage will be same for over the period of time? Sounds like you need a battery replacement. Depending on your iPhone, you can take it to your local Apple Store, and they will replace the battery for $29 dollars. How old is your phone and what model is it?
Chosen Solution I have purchased a MacBook Air early 2014. the previous owner kept their hard drive for data safety so I bought a OWC 240gb SSD. the MacBook Air doesn’t recognise the SSD. The box of the SSD and some searching on the net told me I need to update the firmware on the MacBook Air. I have a 500gb 2.5” SSD from my old broken laptop and so I connected this with an external USB adaptor to the MacBook Air and it booted and worked fine when I booted up and pressed the option key....
Chosen Solution So I have a Sharp Aquos Sh-N01(Japanese Keitai Flip phone) not the above one, but it was the closest one I can find, I inserted a different battery into the phone and only realizing it has a reversed polarity, did I short cut my phone because of this? But I think there should be a reverse polar protection since there was no heat nor smoke. The battery I put in was a smaller battery with less voltage and less wh value....
Chosen Solution my i phone 6 plus touch i c is not working i need a motherboard Why get another motherboard? It’s a risk on doing so because you might get one that is IMEI blocked or iCloud / Apple ID Activation locked meaning you won’t be able to use the phone. Network locked is also a possibility too. You are better off getting the touch IC chip replaced by a professional board repair technician than buying another motherboard which is going to just cost you a lot more at the risk of it being unusable....
Chosen Solution I found that a GBA SP AGS 101 that I’d bought online was having some issues charging due to some corrosion in the charging port. I’d read that distilled white vinegar is good for cleaning corrosion, so I soaked the port in vinegar and scrubbed it clean. Now the charging port works! But I’ve run into another separate issue. Now the speaker has decided to quit working! I tested the speaker in another GBA SP and it works just fine....
Chosen Solution My dishwasher seems to function normally. The dishes seem clean, but the water from the last cycle remains in after it has stopped. The water is clear. I have read the manual and reset the system several times. When I press the cancel button to flush out the remaining water in the morning, you can hear the water being pumped out, and it sounds like the pump is working well....
