Chosen Solution Hi, I’m confused about which components I need to replace my iPad 6th Gen screen. I think I have it right but I’m not sure. I have in my cart the following: iPad Air, iPad 5, iPad 6 Adhesive Strips iPad 5/6/Air 2/mini 4 Home Button Gasket iPad 5/6 LCD iPad 6 Screen Digitizer I already have the Essential Electronics Toolkit, which I think is up to the task....
Chosen Solution I know there’s plenty about this already, but I think this is slightly different. This one self selects etc after 5 minutes of use???? All the tape has been transferred over to the new digitiser so there is no gold contacts showing to touch on the frame. The flex cable is tucked up inside the small gap and not pinched between the glass and frame. I can’t think of what else it could be, especially when it’s after 5 minutes of use (Possibly heat related?...
Chosen Solution the image screen just started showing a bunch of colored lines so cannot take any pics. Hi, Was the camera dropped just before the screen developed the problem? Try taking a picture and then download it to a computer to check if the picture is OK or whether you have a distorted or black image. (I realize that you cannot see what you are taking). If the picture is distorted or black there is a problem with the ccd sensor or the motherboard or both....
Chosen Solution I think i have accidentally deleted my sound device on my laptop as there is no audio for anyhting and cant control sound as there is no device there Kirsty, I don’t think you deleted your sound device :-) You may have deleted the driver for your device. since you did not give us the information about what OS you have, I suggest you get your audio driver from here....
Chosen Solution Hi guys, recently i repair iPhone 6 plus with not touch, I replace Meson and Cumulus, but touch still does not work. After measure, i found shorted line LCM_TO_AP_HIFA_BSYNC to ground. After remove FL2034 is line still shorted to ground on CPU line. I remove U2403 and Meson but does not help. Is there any solution how to repair this issue without reball CPU? Thanks Sorry for my bad English....
Chosen Solution Machine was unable to power on. I tried an SMC reset, and the charger light changed so I know it went through and that the power button works, but the machine still couldn’t power on. I tried a separate battery that was known to work and had some charge on it, and I still wasn’t able to power on. I confirmed the MagSafe 2 board was passing the correct voltage....
Chosen Solution i have a hard drive i want to put in an optical drive caddy for my mac as a second hard drive, does anyone know the r/w speed of the hard drive if i put it in a caddy? Review this page: OWC Data Doubler. Depending on your exact system your optical drives SATA Port is either SATA II (3.0 Gb/s) or SATA III (6.0 Gb/s). Thats still not what your drive is able to push, you’ll need to review your drives spec sheet....
Chosen Solution I am facing issue, my laptop is getting heated again and again. Need permanent solution I had faced same solution a month ago. My laptop started heating and again and shut down after few minutes. I searched on Google and finally found a working solution. You can also follow. https://www.techsguide.com/laptop-troubl…
Chosen Solution What Facebook SHOULD look like What It looks like now. Above is an image of how webpages load. I would like an answer on how to reset safari’s data, and if that does not work, any ideas you will have on how tto rectify this issue without completely factory resetting the device. (that comes later) the device is currently running 10.10.5 + +UPDATE+ + I have downloaded a new browser, (Firefox) which works fine....
Chosen Solution Hi Guys, When I call I don’t hear them, they don’t hear me. If I activate the loudspeaker they hear me and I hear them. When I use the microphone for recording sound it works (=it records). When I listen to recorded sound with my ears, it works (I hear it) even without loudspeaker. Any advice? Apart from that works perfect since I changed the battery with an fixit one, 1 year ago....
Chosen Solution LG Stylo 4 So yesterday my phone started to keep charging and not changing, and loops. I need help ASAP!! @thejonsisback (and loops) is a good indication to start with a new battery. Then check the cable and after that check the charging port.
Chosen Solution Hello I inserted the memory SD card inside my canon 80d. It broke inside, what can I do? Siempremireya, Possibly shake the piece out with with card door open facing down, try sucking it out with a vacuum with small nozzle/crevice tool attached, remove battery and pick broken SD card piece out care fully with tooth pick/metal pin/surgical tweezers or if need be perhaps take into a good local camera repair shop and have them give an estimate to remove broken card piece....
Chosen Solution This guide suggests removing the logic board to replace the trackpad including the trackpad cable. Is it possible, instead, to detach the cable from the existing trackpad and attach it to the new one? This would eliminate the need to remove the logic board. Removing the logic board to replace the screws is absolutely asinine and a COMPLETE waste of time. This is only necessary with 2008 models where they put the screws in the dumbest of places....
Chosen Solution Its a Sony TC 377. Speed is ok but it startsvslow. The 4 Elco’s are broken. I will replace them. If the elco’s on the power suply are broken what should not work? Thanks for reply! @tapedecklover that will depend on the power supply and which part of the circuitry is affecting by that. You do need to either give us a complete number of the power supply and/or post some images of the board....
Chosen Solution I recently replaced a non working power window motor on my 2014 Jetta SE. After the replacement the master switch would only operate the driver’s side window. I’ve tried to no avail to find out if I installed the wrong type motor on the driver’s side or if there’s any difference at all between all of the doors power window motors. Also the switch that does control the driver’s side window is operating in reverse (down is up and up moves the window down) Confused as heck right now and the window motor has stopped working at all now!...
Chosen Solution My ASUS TP 200S , running windows 10 , new , actually about a month old wont turn on the screen when i press the power button , the green power indicator turns on but nothing displays on the screen. What happened before this problem: the laptop would freeze up while in use and indicate a message that the display adapter driver needs to updated , switching to Microsoft basic display driver at times i noticed a square box at the middle of the screen during the driver issues i tried ding a windows 10 upgrade to the latest version available....
Chosen Solution What do I do? Do I get it replaced? And If I do how much will it cost? First off you need to clean the phone completely . The blurriness is likely moisture between the lens and the lens cover on the case. But the phone itself need to be cleaned or it will corrode and die This guide will help with the teardown https://www.youtube.com/watch?v=2wliGGHr…. Clean every connection with a soft toothbrush....
Chosen Solution I’ve had my iPhone since December 27, 2016. After a year of having it my iPhone’s screen started to act weird. Whenever I would click on an app the app next to it would open, or my screen would swipe to the next one. It also likes to open up things whenever i’m not touching it, and even acts like I was trying to move an app or delete one....
Chosen Solution my kenmore elite oasis he has a error message f72 @rober1234 F72 is a basket re-engagement failure. “the most common problem is a nut below the inner tub that needs to “float”. Floating is when the tub fills up with water to a certain level the inner basket will rise about 1 inch from the center agitator. What this does is disengage the basket from the motor so that the agitator can rotate independently from the basket....
Chosen Solution Dear All, I have a MacBook Pro (13-inch, Early 2011) with 2.3 GHz Intel Core i5 processor and 4 GB 1333 MHz DDR3 Memory. My problem is my MacBook Pro is so slow and I’m not sure what I should do to fix this. I’ve read that I can replace the processor and use an SSD hard drive. Should I do this? What brand I should use? Any risks or any important things I need to know beforehand?...
