Chosen Solution No display even in the older crush lcd no light but it has a connection is there any bug in the version on ios 10.1.1 or ill need to open n trace the logic board,,, Is any one had a display ways on ip6???? Hi you need to replace LCD backlight iC , at repair shop this is one of the most common issues for iPhone 6 some time when you heating up the iC it works But i recommend to visit repair shop to replace it
Chosen Solution When I turn on my 40 inch Sony Bravia, the tv clicks and the green light comes on. I don’t have any picture or sound. I’ve been told to shine a light in the dark to see if I can see the picture. I tried it and light just reflects off screen. I can’t see any picture. Any suggestions? Could it still be the inverter board? It was working fine, then one day no picture....
Chosen Solution Not getting spark to spark plug. Changed the igniter coil and still not getting spark to spark plug. Any suggestions as to what to check next or replace next? @tiv check the ignition coil by the flywheel and set the air gap to 0.012 inches.
Chosen Solution When i turn on the machine and nob, the button for making espresso works but there is no water or steam coming from the steam wand, i did check to make sure water flowed through it when i took the wand off.. that was fine. Here’s how to repair the heating element: Testing the Starbucks Barista Heating Element Does any water come out of the machine at all? If the pump is running and there’s water in the tank, water should come from the brewhead until you open the knob, at which point the water will come out of the wand instead....
Chosen Solution Hello Today I tried to update my macos mojave and midway update it restarted 2 times, second one it started beeping and black screen. It fan was spinning fast when it was installing. Now nothing works, tried every command and apple support could not help. Ram was never touched and never been water damaged or dropped. A beep every 5 seconds is provided when no RAM is found by the system....
Chosen Solution Hello, I have got an iPhone 8 that has a loudspeaker (at the bottom) that doesn’t produce any sound. Only the top speaker makes sound. I replaced the loudspeaker with another loudspeaker bought online; this didn’t fix the issue. I already restored the iPhone, factory reset, etc. I have attempted to change the left/right channel audio balance via Accessibility settings, I have tried basically every software solution out there....
Chosen Solution I’ve bought a zoomer dino on Ebay, but I think its faulty. I cannot control his movements - he moves a few times and then goes full speed backwards. It doesn’t stop, inevitavly bumps into something and then keeps on spinning his wheels (while upside down) on max speed. I also have problems getting it into gesture mode. I tried pushing the button on his back but without success....
Chosen Solution Hello, I decided to ask this forum about this issue. My mom’s phone is not charging anymore and we try see if it was dust or small particles but, it was not that. I am wanting to fix the port but, don’t know where to start and My mom does not want buy a new phone. Please help. @bobj2008,Joshua, Google how to factory reset your device as this can sometimes fix charging issues....
Chosen Solution My LG G3 switched off by itself and the battery was at 50%. It now will not switch on. The LG logo start up screen comes on for a second then it goes black and does this repeatedly. The same thing happens when i charge it. The charging icon appears and then flashes on and off. I am not concerned about the phone. What I do want to know it how can I retrieve my photos?...
Chosen Solution My daughter at college dropped her iphone6 in some water and quickly put the phone in rice to dry out. after few days she powered up and seem to work fine but there was no sound in the earpiece speaker though the headphones,loud speaker & Bluetooth ear piece worked. After reading a number of posts on water damage I figured the headphone jack port was damaged so I replaced the Headphone Jack Flex Cable (also the cracked screen while I was at it)....
Chosen Solution I replaced the touch screen on my iphone 3G. The top power button is jammed and wont respond. Other problem is that the LCD has horizontal lines and colors are all opposite. Any suggestions You can unscrew the bracket to the power button and hope you can readjust. Sometimes the housing and the bezel separates and this can cause the same issue. You’d have to glue the bezel back to the housing....
Chosen Solution I have a connection to the hand held brush, But not a good connection to main vacuum cleaner brush. The main part of the Hoover isn’t making a good connection to the long pipe to drive brush. If your Shark vacuum stops moving suddenly during use, see the Shark ION Robot R75 Stops Moving Unexpectedly problem page for possible problems and solutions. First check to make sure all the connection terminals are clean, if they are all making contact check to see if your motor is blown....
Chosen Solution My original problem was a bad hard drive. It would load to the gray screen with the Apple logo and the windmill, then it would freeze. I since replaced the HD, but now it beeps 3 times when I turn on the laptop. I replaced the RAM, but it still gives me the 3 beeps when I turn on the laptop. It’s still a RAM problem. Could be you put the wrong RAM in and could be a bad RAM slot....
Chosen Solution Hello, I have a 2004 Cub Cadet LT1024 Riding Mower and it is having a hard time cranking. Like it will roll over but stop in mid rotation and have to use my hand to help it rotate. Will never make a full rotation and will not start. I have replaced the starter, battery, coils, plugs, fuel pump. I have checked the carb and it is flowing like should....
Chosen Solution I just replaced the screen on my iPhone 7 Plus. After the screen replacement I noticed that the proximity sensor was getting extremely hot when the phone was in use. Is this out of the ordinary? If so, what is the possible cause of this issue? When i used to repair iPhones professionally overheating proximity sensors where pretty much always the result of a damaged flex cable or a component coming loose from the flex cable....
Chosen Solution My drift Stealth 2 has a reddish blurry mark with 2 light lines top right hand corner when recording - I cleaned the lens - red is lighter but still a bit blurry - why?? JJ Nel sounds like a damaged light/UV sensor For that you would have to get into the lens assembly and replace the sensor. Problem is that there is not guide as of yet and not even sure if you can get replacement parts....
Chosen Solution I got this issue with my old powermac G4 EMC#1896, when I start the computer after a couples of minutes all of the sudden it shut off by itself..!! then I wait, I turn it on again, and same happen again it goes off I would recommend reading over this answer I wrote. It sounds like you have a slightly different situation, but the problem is likely very similar, and I suspect the solution would be the same....
Chosen Solution My 2012 laptop has a stuck Control key, although it isn’t really stuck. it functions normally but the computer thinks it’s always pressed. any way of fixing or deactivating it? I popped the key cover off and cleaned it with air and a small brush but that didn’t help. the little rubber thingy functions as it should. Never had any liquid or food dropped on it either. Sometimes things break on their own, even on a 10/11 years old Mac....
Chosen Solution My iPhone 3GS was pee’d on by my drunk friend who slept with it the other night at a party. He didn’t tell me till the next afternoon which the camera was still moist and foggy. So i dried it up but idk if he tried turning it on. Two days goes by and nothing works, so i decide to open it up and look at the logic board and the copper contacts attached to the battery are corroded and have like little dark spots....
Chosen Solution Hey if I have a MacBook pro 13 unibody 2009 2.26 ghz . And my board got damaged and I want to replace it . Can I replace it with the 2.4 board ? I really need your help so please answer me fast thanks allot I think you would have better luck upgrading to this machines board: Apple MacBook Pro “Core 2 Duo” 2.53 13" (SD/FW) Specs Identifiers: Mid-2009 13" - MB991LL/A - MacBookPro5,5 - A1278 - 2326*...
