Chosen Solution my dvd drive was not working offcourse cd drive was working.so please suggest me how to repair it. anusha, this could be caused by misaligned/dirty lasers or bad diodes. You could try and clean the drive with some commercially available lens cleaner. If that dos not work, you may have to replace the drive. To see how to replace the optical drive, use this guide. Hope this helps, good luck....
Chosen Solution Compressor is running and getting hot condenser not getting hot evap not getting cold and I changed the filter what the problem? Hi @kentonp , If the evaporator is not getting freezing cold then there could be a problem with a lack of refrigerant in the system. Here is a link that may help
Chosen Solution I was just surfing the net, and my mbp straight up dies. When it was on, the battery was fully charged. The MagSafe was green. Now, the MagSafe does not light at all, and I can’t reset the smc. It seems unlikely that my power cable is all of a sudden faulty and this caused my Computer to die completely, so I’m guessing its an internal problem. Does anyone have a place they think I should start?...
Chosen Solution i was just using my pc normally and suddenly my pc just restarts and before I knew it my monitor stopped using my gpu I tried restarting and it didn’t work I tried disabling the integrated graphics card in device manger and then connecting the cable to my gpu and it still didn’t work pls help me Hi, Does your model GPU card have provision for a power cable to be connected to it?...
Chosen Solution When I type on the keyboard, nothing is showing up on the tablet screen. What can I do? One reason this could be happening is due to the connection between the keyboard and the tablet. The connection where the keyboard and the tablet meet could be faulty or misplaced. Remove the keyboard from the tablet and examine the magnetic hinge in the center of the keyboard. If it is damaged, you will need to buy a new keyboard....
Chosen Solution I am not sure what’s going on here. My Touch screen just not working properly. I tried replace 2 new screens but still not working. Is it intermittently not working at all, ghost touching or dead spots? If it’s intermittently not working at all in most cases the touch ic chip needs to be replaced by someone that does micro soldering. Ghost touching and dead spots are caused by bad screens....
Chosen Solution Hi, I’ve got an iPhone XR that keeps on rebooting on random occasions. I did notice when the front facing camera is plugged in, it doesn’t recognise it. So I thought I’d take the initiative and see why this is the case under my brand new AmScope microscope! (NerdGasm). The reading’s I’m receiving from my multimeter are majorly all saying OL and some of them have the odd very low diode readings; such as 0....
Chosen Solution I successfully swapped out the original Seagate 1Tb drive in my 27" iMac for the above 3Tb drive (and a Samsung EVO 250Gb SSD) a week or so ago and everything went very smoothly. Unfortunately I’m now getting an issue where the internal 3Tb Seagate will randomly ’eject’ and I’m not able to mount it again without rebooting the machine from scratch. It seems to happen if a large ‘copy’ process is initiated - i was trying to automatically recover my iTunes library by bringing all my files back to the drive from iTunes Match using ‘Make Available Offline’…it gets so far and then stops/ejects :( For info the machine is i7 3....
Chosen Solution Is this normal? I don’t have any games yet. I just want to make sure that theres not something wrong with it before I spend money on it. Hi @e_ah Yea… when you on without cartridge. best to test with a known cartridge https://www.youtube.com/watch?v=x4iXjJB2… It happens sometimes. Your battery may need to be replaced.
Chosen Solution I adopted a liquid-damaged MacBook Air which was completely non-responsive. I took it apart and saw signs of liquid intrusion, with some corrosion around the I/O ribbon cable connection (mostly on the logic board side but both needed cleaning). I tried cleaning the existing cable and connectors and managed to get it to boot, but not charge. The cable looked like it caught the worst of the corrosion so I replaced it and now the laptop works normally aside from not detecting an audio device (About this Mac > System Report shows no audio device: audio controls are greyed out in System Prefs)....
Chosen Solution I just replaced my iPhone 5 Lightning Connector and Headphone Jack because my lighting connector was broken, but I have a very weak single (only one point), or most of times, it shows “No Service”, But it has a strong wi-fi single, I can access internet. Is it an issue with antenna? In addition, I found my battery lost power quite fast after I replaced the part, it only has 70% power remaining for one night....
Chosen Solution Did a charge port replacement on a note 5. After, the phone will only search for signal. Is that because I did not use the right charge port that is compatible with that carrier? Yeah that is probably the case. The charging port variants have the antenna connector prongs in different locations which is why I do charger port replacements via soldering and not the whole charging daughter board....
Chosen Solution there is no sound on my TV Here’s some advice from Sony’s troubleshooting website if you are having good picture but no sound: Check the volume level. Press MUTING or VOL + so that “Muting” disappears from the screen. Set Speakers to TV Speakers in the Sound settings. If it is set to Audio System, sound is not output from the TV’s speakers regardless of the TV’s volume control....
Chosen Solution Hi All, The sound on my iPad all of a sudden stopped working. The sound works fine with headphones in and I can change the volume, but when I unplug the headphones I get absolutely no sound from the speaker, and I can’t even change the volume. I originally thought this must have been a software issue so I went through all the settings, checked mute etc. After that, I tried a reset using the power and home button, and I even restored to factory settings....
Chosen Solution A few days ago I started up my iMac (21.5" / Mid-2010) I felt the fans running, heard the boot chime and everything seemed fine except there was no video, no backlight, nothing at all on the display. I pressed the play button on the keyboard and iTunes started and played a song. So I restarted the computer, did the SMC reset, connected it to an external display but still no video....
Chosen Solution The Dash, P, Return, Optical drive eject, and volume not working on my keyboard. Most likely is that your keyboard received a small amount of liquid damage and shorted out that group of keys. You will need to replace either the keyboard or the upper case. MacBook Pro 15" Unibody Early 2011 Upper Case Replacement How can I replace the keyboard?
Chosen Solution I have this patern on the display of a 2008 iMac I am between the LCD or graphics board That’s definitely the GPU board. Failing GPUs tend to make pretty patterns like that. Please confirm your iMac’s EMC number so we can find you the proper part. How do I find my iMac’s EMC number? Update (11/21/2018) Perfect! Here is a link to a replacement GPU and here is a link to a tutorial on how to replace the GPU....
Chosen Solution I just changed the battery on my moto g6, but the new battery wasn’t charging for some reasons. The only damage I could have done to the phone was when I was taking it apart, I slightly touched apart of the motherboard with some tweezers, and I carefully cleaned the motherboard with some 91% isopropyl alcohol and a small brush. I have tried using different cables and charging bricks, but it only charges to three percent when turned off, but not when turned on....
Chosen Solution Hello everyone, I had replaced my screen a few weeks ago and I all ready know it has nothing to do with that. But I had realized my battery was bad so I got a new one my phone was died before I took old battery out and put the new one in but it’s been more then 24 hours and my phone still won’t turn on. I did try the Apple boot loop and that didn’t even work....
Chosen Solution I plugged my 110v hand blender in a 220v power source. It made a flash, and never turned on again, so we can assume its burned, right? What exactly was damaged? Is it possible to fix it? How? Where do I buy the parts needed to do it? pedro, the only way to determine exactly what has overloaded is by taking the blender apart. Most likely it is the caps (potentially a fuse on a circuit board) or even the motor....
